AIROSOL COMPANY, INC.

MCKAY CHEMICALS MECHANICS BRAND

1101 Illinois, PO Box 120, Neodesha KS 66757 - Phone 620-325-2666

MATERIAL SAFETY DATA SHEET

PRODUCT NAME:	Oil Treatment (Saver, Plate)	HMIS Codes:	H	F	R	P
PRODUCT CODE:	50101MB		0	1	0	0

SECTION I - MANUFACTURER IDENTIFICATION

MANUFACTURER’S NAME:	Airosol Company, Inc.
ADDRESS:	PO Box 120, Neodesha KS 66757
EMERGENCY PHONE:	1-800-535-5053
INFORMATION PHONE:	1-800-633-9576
DATE REVISED:	1/5/2002

SECTION I I- HAZARDOUS INGREDIENTS/SARA III INFORMATION

OCCUPATIONAL EXPOSURE LIMITS

HAZARDOUS COMPONENTS	CAS NUMBER	OSHA	ACIGH	%
Severely Hydrotreated Heavy Naphthenic Petroleum Oil Proprietary Oil Soluble Polymer Blends	64742-52-5 N/A	5 mg/m3 5 mg/m3	5 mg/m3 5 mg/m3	90-97 3-10
The composition of this mixture may be proprietary information. In the event of a medical emergency, compositional information will be provided to a physician or nurse.

All chemical compounds marked with an Asterisk (*) are toxic chemicals subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act (SARA) of 1985 and 40 CFR Part 372. You must notify each person to whom this mixture or trade name product is sold. This statement must remain a part of this Material Safety Data Sheet.

SECTION III- PHYSICAL/CHEMICAL CHARACTERISTICS

BOILING POINT:	> 500°F	SPECIFIC GRAVITY:	0.91 @ 60°F
VAPOR DENSITY:	> 5 (Air = 1)	EVAPORATION RATE:	1000 x slower than ethyl ether
APPEARANCE AND ODOR:	Pale straw to yellow, Light bland petroleum oil odor	SOLUBILITY IN WATER:	Insoluble

SECTION IV- FIRE AND EXPLOSION HAZARD DATA

FLASH POINT:	> 300°F			METHOD USED:		COC
FLAMMABLE LIMITS IN AIR BY VOLUME:				LOWER:	N/D		UPPER:	N/D
EXTINGUISHING MEDIA:		Dry chemical, foam or water spray.
SPECIAL FIREFIGHTING PROCEDURES: Wear self-contained breathing apparatus and full protective clothing.
UNUSUAL FIRE AND EXPLOSION HAZARDS:			Fumes, smoke, carbon monoxide.

SECTION V- REACTIVITY DATA

STABILITY: Stable

CONDITIONS TO AVOID: Do not heat over 140°F to avoid possible release of hydrogen sulfide.

Page 1 of 3

PRODUCT NAME:	Oil Treatment (Saver, Plate)
PRODUCT CODE:	50101MB

SECTION V- REACTIVITY DATA (continued)

INCOMPATIBILITY (MATERIALS TO AVOID): Strong oxidizing agents.

HAZARDOUS DECOMPOSITION OR BYPRODUCTS: Hydrogen sulfide, carbon monoxide, and carbon dioxide from burning, oxides of nitrogen and oxides of sulfur.

HAZARDOUS POLYMERIZATION: Will not occur.

SECTION VI- HEALTH HAZARD DATA

INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Negligible hazard at ambient temperature (0 to 100° F, -18 to 38°C). Avoid breathing vapors or mists.

NATURE OF HAZARD:

EYES:	Minimal irritation upon contact.
SKIN:	May cause mild skin irritation with prolonged and repeated contact.
INGESTION:		Minimal toxicity.
CARCINOGENICITY:			NTP?	IARC?	OSHA REGULATED?
Presently not on any list.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: NA

EMERGENCY AND FIRST AID PROCEDURES

INHALATION: Using proper respiratory protection, immediately remove the affected victim from exposure.

Administer artificial respiration if breathing is stopped. Keep at rest. Call for prompt medical attention.

SKIN AND EYE CONTACT:

EYES: Immediately flush eyes with large amounts of water for at least 15 min. If irritation persists, get medical attention immediately.

SKIN: First aid is normally not required. Wash exposed skin completely with soap and water. Remove grossly contaminated clothing, including shoes, and launder before reuse. To remove hot product from skin, immediately immerse in large amounts of cold water to dissipate heat and reduce extent of thermal burns. Solid product may be removed from skin with pharmaceutical grade mineral oil or food grade vegetable oil. If irritation occurs consult a physician.

SECTION VII- PRECAUTIONS FOR SAFE HANDLING AND USE

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Eliminate sources of ignition. Prevent additional discharge of material if possible to do so without hazard. For small spill implement cleanup procedures and, if in public area, keep public away and advise authorities. Prevent liquid from entering sewers, watercourses, or low areas. Contain spilled liquid with sand or earth.

WASTE DISPOSAL METHOD: Dispose in accordance with federal, state, and local regulations regarding pollution.

PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Keep away from heat, sparks, or open flame.

OTHER PRECAUTIONS: N/A

SECTION VIII- CONTROL MEASURES

RESPIRATORY PROTECTION: Usually not required if it is used as it is described on the label.

VENTILATION: Provide adequate ventilation to keep mist or vapors below allowable exposure levels.

PROTECTIVE GLOVES: For prolonged or repeated contact, wear gloves( acceptable glove material polyvinyl chloride, neoprene, nitrile, poly vinyl alcohol, and viton).

Page 2 of 3

PRODUCT NAME:	Oil Treatment (Saver, Plate)
PRODUCT CODE:	50101MB

SECTION VIII- CONTROL MEASURES (continued)

EYE PROTECTION: Recommend safety glasses with unperforated sideshields.

OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Long sleeves and long pants.

WORK/HYGIENIC PRACTICES: Wash hands after use.

SECTION IX- DISCLAIMER

DISCLAIMER: The information in this document is believed to be correct as of the date issued. However, no warranty of merchantability, fitness for any particular purpose, or any other warranty is expressed or to be implied regarding the accuracy or completeness of this information or the product, the safety of this product, or the hazards related to its use. This information and product are furnished "as is" and on the condition that the person receiving them shall make their own determination as to the suitability of the product for their particular purpose and on the condition that they assume the risk of their use thereof.

Page 3 of 3